|
ru.unix.bsd- RU.UNIX.BSD ------------------------------------------------------------------ From : Nikolai Saoukh 2:5020/400 14 Jan 2003 14:18:12 To : Sergey Matveychuk Subject : Re: mpd - глюкало -------------------------------------------------------------------------------- | И вообще мне не помог ни один совет, ни set iface mtu 1400, ни | установка multilink в XP. Как пакеты терялись, так и продолжают :(( | Разве что пореже. Hо все равно mpd - не рабочий вариант для XP. | Файлы скачивать совершенно не возможно. :((( Проблема не в mpd, поверьте мне. Я бодаюсь с этой проблемой уже давно. Ровно также не работает pppd (вместе с l2tpd). Баг этот очень редкий (по виду) и изощренный. Hе могли бы Вы воспроизвести (прислать мне) конфигурацию ядра (config) и выдачу dmesg. Вот мои данные ----- cut here to destroy your CRT ---- machine i386 cpu I586_CPU cpu I686_CPU ident FOOBAR maxusers 0 options INET options FFS options FFS_ROOT options SOFTUPDATES options UFS_DIRHASH options PROCFS options COMPAT_43 options SCSI_DELAY=3000 options UCONSOLE options KTRACE options SYSVSHM options SYSVMSG options SYSVSEM options P1003_1B options _KPOSIX_PRIORITY_SCHEDULING options ICMP_BANDLIM options KBD_INSTALL_CDEV options IPFIREWALL options IPDIVERT options IPSEC options IPSEC_ESP device isa device pci device fdc0 at isa? port IO_FD1 irq 6 drq 2 device fd0 at fdc0 drive 0 device bt device scbus device da device pass device atkbdc0 at isa? port IO_KBD device atkbd0 at atkbdc? irq 1 flags 0x1 device psm0 at atkbdc? irq 12 device vga0 at isa? pseudo-device splash device sc0 at isa? flags 0x100 device npx0 at nexus? port IO_NPX irq 13 device apm0 at nexus? disable flags 0x20 device sio0 at isa? port IO_COM1 flags 0x10 irq 4 device sio1 at isa? port IO_COM2 irq 3 device ppc0 at isa? irq 7 device ppbus device lpt device ppi device de pseudo-device bpf pseudo-device ether pseudo-device loop pseudo-device pty ----- cut here to destroy your CRT ---- Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.7-STABLE #21: Tue Jan 14 09:38:52 MSK 2003 nms@Draculina.otdel-1.org:/usr/src/sys/compile/DRACULINA Calibrating clock(s) ... TSC clock: 360837404 Hz, i8254 clock: 1193246 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz CLK_USE_TSC_CALIBRATION not specified - using old calibration method CPU: AMD-K6(tm) 3D processor (360.82-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX> AMD Features=0x80000800<SYSCALL,3DNow!> Data TLB: 128 entries, 2-way associative Instruction TLB: 64 entries, 1-way associative L1 data cache: 32 kbytes, 32 bytes/line, 2 lines/tag, 2-way associative L1 instruction cache: 32 kbytes, 32 bytes/line, 2 lines/tag, 2-way associative Write Allocate Enable Limit: 128M bytes Write Allocate 15-16M bytes: Enable real memory = 134217728 (131072K bytes) Physical memory chunk(s): 0x00001000 - 0x0009ffff, 651264 bytes (159 pages) 0x002fe000 - 0x07ff7fff, 131047424 bytes (31994 pages) avail memory = 127770624 (124776K bytes) bios32: Found BIOS32 Service Directory header at 0xc00faeb0 bios32: Entry = 0xfb330 (c00fb330) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xb360 pnpbios: Found PnP BIOS data at 0xc00fbeb0 pnpbios: Entry = f0000:bed8 Rev = 1.0 Other BIOS signatures found: ACPI: 00000000 Preloaded elf kernel "kernel" at 0xc02d7000. K6-family MTRR support enabled (2 registers) pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=12508086) Using $PIR table, 5 entries at 0xc00fdb70 npx0: <math processor> on motherboard npx0: INT 16 interface i586_bzero() bandwidth = 160978750 bytes/sec bzero() bandwidth = 160642570 bytes/sec pcib0: <Host to PCI bridge> on motherboard found-> vendor=0x8086, dev=0x1250, revid=0x03 class=06-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 found-> vendor=0x8086, dev=0x7000, revid=0x01 class=06-01-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 found-> vendor=0x8086, dev=0x7010, revid=0x00 class=01-01-80, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 found-> vendor=0x104b, dev=0x1040, revid=0x00 class=01-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=15 map[10]: type 1, range 32, base 00006400, size 2 found-> vendor=0x8086, dev=0x1229, revid=0x05 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[10]: type 1, range 32, base e0100000, size 12 map[14]: type 1, range 32, base 00006800, size 5 map[18]: type 1, range 32, base e0000000, size 20 found-> vendor=0x1011, dev=0x0009, revid=0x12 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[10]: type 1, range 32, base 00006c00, size 7 map[14]: type 1, range 32, base e0101000, size 7 pci0: <PCI bus> on pcib0 isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0 I/O Recovery Timing: 8-bit 3 clocks, 16-bit 2 clocks Extended BIOS: disabled Lower BIOS: disabled Coprocessor IRQ13: enabled Mouse IRQ12: disabled Interrupt Routing: A: IRQ15, B: IRQ11, C: IRQ10, D: disabled MB0: disabled, MB1: isa0: <ISA bus> on isab0 pci0: <Intel PIIX3 ATA controller> (vendor=0x8086, dev=0x7010) at 7.1 bt0: <Buslogic Multi-Master SCSI Host Adapter> port 0x6400-0x6403 irq 15 at device 8.0 on pci0 bt0: BT-946C FW Rev. 4.25J Narrow SCSI Host Adapter, SCSI ID 7, 100 CCBs bt0: Using Strict Round Robin Mailbox Mode pci0: <unknown card> (vendor=0x8086, dev=0x1229) at 9.0 irq 11 de0: <Digital 21140 Fast Ethernet> port 0x6c00-0x6c7f mem 0xe0101000-0xe010107f irq 10 at device 10.0 on pci0 de0: SMC 9332DST 21140 [10-100Mb/s] pass 1.2 de0: address 00:00:c0:e0:9e:d0 de0: enabling 10baseT port bpf: de0 attached Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcc7ff on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0067 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 psm0: current command byte:0067 psm0: failed to reset the aux device. vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0: irq maps: 0x41 0x51 0x41 0x41 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: irq maps: 0x41 0x49 0x41 0x41 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: parallel port found at 0x378 ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/16 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 isa_probe_children: probing PnP devices BIOS Geometries: 0:03ff3f20 0..1023=1024 cylinders, 0..63=64 heads, 1..32=32 sectors 0 accounted for Device configuration finished. bpf: lo0 attached IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging disabled IPsec: Initialized Security Association Processing. Waiting 3 seconds for SCSI devices to settle bt0: Using Strict Round Robin Mailbox Mode bt: ccb 0xc8212340 - error 4 occured. btstat = 11, sdstat = 0 bt: ccb 0xc8212300 - error 4 occured. btstat = 11, sdstat = 0 bt: ccb 0xc82122c0 - error 4 occured. btstat = 11, sdstat = 0 bt: ccb 0xc8212280 - error 4 occured. btstat = 11, sdstat = 0 bt: ccb 0xc8212240 - error 4 occured. btstat = 11, sdstat = 0 bt: ccb 0xc8212200 - error 4 occured. btstat = 11, sdstat = 0 bt: ccb 0xc8212280 - error 4 occured. btstat = 0, sdstat = 2 Creating DISK da0 pass0 at bt0 bus 0 target 0 lun 0 pass0: <FUJITSU M2949ESP SUN9.0G 2848> Fixed Direct Access SCSI-2 device pass0: Serial Number 00063793 pass0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled da0 at bt0 bus 0 target 0 lun 0 da0: <FUJITSU M2949ESP SUN9.0G 2848> Fixed Direct Access SCSI-2 device da0: Serial Number 00063793 da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled da0: 8637MB (17689267 512 byte sectors: 64H 32S/T 8637C) Mounting root from ufs:/dev/da0s1a da0s1: type 0xa5, start 32, end = 17688575, size 17688544 : OK start_init: trying /sbin/init de0: enabling 100baseTX port de0: enabling Full Duplex 100baseTX port fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x6800-0x681f mem 0xe0000000-0xe00fffff,0xe0100000-0xe0100fff irq 11 at device 9.0 on pci0 fxp0: using memory space register mapping fxp0: Ethernet address 00:08:c7:b9:d7:82 fxp0: PCI IDs: 8086 1229 0e11 b0d7 0005 fxp0: Dynamic Standby mode is disabled bpf: fxp0 attached inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto splash: image decoder found: green_saver (pass0:bt0:0:0:0): tagged openings now 2 bpf: ng0 attached bpf: ng1 attached ----- cut here to destroy your CRT ---- --- ifmail v.2.15dev5 * Origin: Gamma NNTP server Moscow Russia (2:5020/400) Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
Архивное /ru.unix.bsd/75912f1f34d1.html, оценка из 5, голосов 10
|