|
ru.unix.bsd
- RU.UNIX.BSD ------------------------------------------------------------------
From : Alexandr Moskalenko 2:5020/400 12 Dec 2002 12:30:33
To : Dima Veselov
Subject : Re: Что значит WRITE command timeout...
--------------------------------------------------------------------------------
Dima Veselov wrote:
> Вечно-добpое утpо, Alexandr!
>
> 10 Дек 02 Alexandr и Eugene сидели на трубе:
>
> >> K> ad0: WRITE command timeout tag=0 serv=0 - reseting
> >> K> ata0: Reseting device done
> >> K> В принципе перевод понятен, но причина нет. Что это глюкавая
> >> K> мать или не тот драйвет ИДЕ портов или что?
> >> Версию системы, навание матери и винтов Пушкин будет говорить?
> AM> аналогичная проблема
> AM> $ uname -sr
> AM> FreeBSD 4.5-STABLE
> AM> MB - Intel 440 LX
> AM> HD - 3079MB <QUANTUM FIREBALL ST3.2A> [6256/16/63]
>
> Может для разнообразия dmesg покажем? Hу кусочек хотя бы. :F
>
> Sincerelly yours.
>
вот, сегодня загрузилась попытки с 5-6 после вчерашнего жесткого
вырубания, ругалась на отсутствие какой-то там kernel page
тачка так, для експериментов, ценного ничего нет, но будет жалко если помрет
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #0: Fri Sep 27 16:14:03 EEST 2002
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (233.86-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x634 Stepping = 4
Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 67096576 (65524K bytes)
avail memory = 62590976 (61124K bytes)
Preloaded elf kernel "kernel" at 0xc02ae000.
Pentium Pro MTRR support enabled
Using $PIR table, 7 entries at 0xc00f0d40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443LX (440 LX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443LX (440 LX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 4.2
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at
device 4.3 on pci0
rl0: <RealTek 8139 10/100BaseTX> port 0xd000-0xd0ff mem
0xe3000000-0xe30000ff irq 10 at device 9.0 on pci0
rl0: Ethernet address: 00:00:21:d5:c4:49
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <S3 ViRGE DX/GX graphics accelerator> at 12.0 irq 11
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
IP packet filtering initialized, divert disabled, rule-based forwarding
disabled, default to accept, logging limited to 100 packets/entry by default
DUMMYNET initialized (011031)
ad0: 3079MB <QUANTUM FIREBALL ST3.2A> [6256/16/63] at ata0-master UDMA33
Mounting root from ufs:/dev/ad0s1a
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0-slave: ATA identify retries exceeded
done
WARNING: / was not properly dismounted
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ad0: timeout sending command=ef s=d0 e=00
ad0: trying fallback to PIO mode
ata0: resetting devices .. done
--- ifmail v.2.15dev5
* Origin: A poorly-installed InterNetNews site (2:5020/400)
Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
|
Re: Что значит WRITE command timeout... 