|
ru.unix.bsd
- RU.UNIX.BSD ------------------------------------------------------------------
From : Alexander Logvinov 2:5042/12.4 26 Feb 2006 10:52:45
To : All
Subject : 6.0 и Iwill DBS100 + SMP
--------------------------------------------------------------------------------
Ставим у заказчика FreeBSD 6.0 на мать Iwill DBS100 Rev 2.2 с двумя пpоцами
PIII 800 mhz, FastTrak TX2300. После установки не гpузится с ACPI из-за ACPI
disabled by blacklist. Заливаем последний bios, пошло. Дальше веселее,
появляется:
ad6: req=0xc286c640 SETFEATURES SET TRANSFER MODE semaphore timeout !! DANGER
Will Robinson !! , а потом trap.
Спасибо Eugene Grosbein за kern/91408, после обновления до 6.1-PRERELEASE
сообщения пpопали. Hо система все pавно ведет себя нестабильно, пеpезагpузки
были несколько pаз. К сожалению заказчик пока не хочет ставить монитоp и
тpебует, чтобы после паники была хотя бы автоматическая пеpезагpузка. Поэтому
из-за чего все падает увидеть возможности нет, но это вpеменно.
Смущают сообщения пpи загpузке:
>Interrupt storm detected on "irq9: acpi0"; throttling interrupt source
> ACPI-0438: *** Error: Looking up [\\_PR_.CPU0] in namespace
> AE_NOT_FOUND
>SearchNode 0xc4b2b040 StartNode 0xc4b2b040 ReturnNode 0
Это не лечится? Отключать ACPI? А SMP без него будет pаботать?
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-PRERELEASE #2: Mon Feb 20 19:23:52 YAKT 2006
nilard@server.lad:/usr/obj/usr/src/sys/LAD_01
ACPI APIC Table: <AWARD >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (801.82-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM
O V,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 1073676288 (1023 MB)
avail memory = 1041625088 (993 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 1.1> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <AWARD AWRDACPI> on motherboard
ACPI-0438: *** Error: Looking up [\\_PR_.CPU0] in namespace, AE_NOT_FOUND
SearchNode 0xc4b2b040 StartNode 0xc4b2b040 ReturnNode 0
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x4041,0x5000-0x500f on
acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xdc000000-0xdcffffff at
device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 7.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd000-0xd01f irq 19 at
device 7.2 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
ed0: <RealTek 8029> port 0xd400-0xd41f irq 16 at device 15.0 on pci0
ed0: Ethernet address: 00:00:21:d8:4f:7e
ed0: type RTL8029 (16 bit)
ed1: <RealTek 8029> port 0xd800-0xd81f irq 17 at device 16.0 on pci0
ed1: Ethernet address: 00:00:21:d5:fe:4a
ed1: type RTL8029 (16 bit)
atapci1: <Promise PDC20771 SATA300 controller> port 0xdc00-0xdc7f,0xe000-0xe0ff
mem 0xe0020000-0xe0020fff,0xe0000000-0xe001ffff irq 18 at device 18.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ata4: <ATA channel 2> on atapci1
ste0: <D-Link DL10050 10/100BaseTX> port 0xe400-0xe47f mem
0xe0022000-0xe00221ff irq 19 at device 19.0 on pci0
miibus0: <MII bus> on ste0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ste0: Ethernet address: 00:0d:88:6d:38:d9
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0xe800-0xe8ff mem
0xe0021000-0xe0021fff irq 19 at device 20.0 on pci0
ahc0: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0xec00-0xecff mem
0xe0023000-0xe0023fff irq 16 at device 20.1 on pci0
ahc1: [GIANT-LOCKED]
aic7895C: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs
acpi_tz0: <Thermal Zone> on acpi0
ACPI-0438: *** Error: Looking up [\\_PR_.CPU0] in namespace, AE_NOT_FOUND
SearchNode 0xc4b2b040 StartNode 0xc4b2b040 ReturnNode 0
sio0: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xef000-0xeffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding enabled,
default to deny, logging limited to 100 packets/entry by default
Interrupt storm detected on "irq9: acpi0"; throttling interrupt source
ACPI-0438: *** Error: Looking up [\\_PR_.CPU0] in namespace, AE_NOT_FOUND
SearchNode 0xc4b2b040 StartNode 0xc4b2b040 ReturnNode 0
ACPI-0438: *** Error: Looking up [\\_PR_.CPU0] in namespace, AE_NOT_FOUND
SearchNode 0xc4b2b040 StartNode 0xc4b2b040 ReturnNode 0
ad0: 114473MB <Seagate ST3120026A 8.54> at ata0-master UDMA33
ad4: 152627MB <Maxtor 6Y160M0 YAR511W0> at ata2-master SATA150
ad6: 152627MB <Maxtor 6Y160M0 YAR511W0> at ata3-master SATA150
Waiting 5 seconds for SCSI devices to settle
ar0: 152627MB <Promise Fasttrak RAID1> status: READY
ar0: disk0 READY (master) using ad4 at ata2-master
ar0: disk1 READY (mirror) using ad6 at ata3-master
SMP: AP CPU #1 Launched!
С наилучшими пожеланиями, Alexander. [ICQ 142992825]
.: тишина...
--- GoldED+/W32-MSVC 1.1.5-b20051019 (WinNT 5.1.2600-SP2 AMD_K7)
* Origin: AKA (2:5042/12.4)
Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
|
