|
ru.unix.bsd
- RU.UNIX.BSD ------------------------------------------------------------------
From : Illia Baidakov 2:5020/400 03 Sep 2004 11:22:15
To : Boris Samorodov
Subject : Re: puc и Netmos NM9835 вызывает panic: как сконфигурить?
--------------------------------------------------------------------------------
> И скорее всего начиная с sio4. А sio6-9 disable.
написал так:
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
device puc
options PUC_FASTINTR
options COM_MULTIPORT
device sio4 at isa? port 0xb000 flags 0x901
device sio5 at isa? port 0xb400 flags 0x901
device sio6 at isa? disable port 0xb800 flags 0x901
device sio7 at isa? disable port 0xbc00 flags 0x901
device sio8 at isa? disable port 0xc000 flags 0x901
device sio9 at isa? disable port 0xcc00 flags 0x901 irq 19
получил вот что:
(сразу обращаю внимание на строчку
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 19
т.е. устройство хочет получить то же прерывание, что и автоматически
дается моей NetMos карте.
на этом основании я и прописал для sio4-9 irq 19.
как принудительно назначить карте другое прерывание?
как выбрать свободное прерывание?).
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-STABLE #5: Fri Sep 3 10:31:44 MSD 2004
...skip...
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2394.01-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,
MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1072889856 (1047744K bytes)
avail memory = 1041301504 (1016896K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc03a1000.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00f3310
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 16
IOAPIC #0 intpin 18 -> irq 17
IOAPIC #0 intpin 23 -> irq 18
IOAPIC #0 intpin 17 -> irq 19
pci0: <PCI bus> on pcib0
agp0: <Intel 82875P host to AGP bridge> mem 0xf8000000-0xfbffffff at
device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=8086 device=2579)> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on
pci0
pci2: <PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port
0x9c00-0x9c1f mem 0xfc9e0000-0xfc9fffff irq 17 at device 1.0 on pci2
em0: Speed:N/A Duplex:N/A
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xe000-0xe01f irq
2 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xe400-0xe41f irq
16 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xe800-0xe81f irq
17 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xec00-0xec1f irq
2 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 18
pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on
pci0
IOAPIC #0 intpin 21 -> irq 20
IOAPIC #0 intpin 20 -> irq 21
pci3: <PCI bus> on pcib3
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0xc400-0xc4ff mem
0xfeafe000-0xfeafefff irq 20 at device 0.0 on pci3
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
puc0: <NetMos NM9835 Dual UART and 1284 Printer port> port
0xb000-0xb00f,0xb400-0xb407,0xb800-0xb807,0xbc00-0xbc07,0xc000-0xc007,0xc
c00-0xcc07 irq 19 at device 2.0 on pci3
sio10: configured irq 19 not in bitmap of probed irqs 0
sio10: type 16550A
sio11: configured irq 19 not in bitmap of probed irqs 0
sio11: type 16550A
pci3: <ATI Mach64-GR graphics accelerator> at 6.0 irq 21
fxp0: <Intel 82801BA (D865) Pro/100 VE Ethernet> port 0xac00-0xac3f mem
0xfeafd000-0xfeafdfff irq 21 at device 8.0 on pci3
fxp0: Ethernet address 00:0c:f1:7f:fa:f7
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on
pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 ATA100 controller> port
0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 irq 17 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 19
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio4: configured irq 19 not in bitmap of probed irqs 0
sio5: configured irq 19 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding
enabled, default to deny, logging limited to 100 packets/entry
by default
DUMMYNET initialized (011031)
SMP: AP CPU #1 Launched!
acd0: MODE_SENSE_BIG command timeout - resetting
ata0: resetting devices .. done
acd0: CDROM <ASUS CD-S520/A> at ata0-slave PIO4
Waiting 3 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST336607LW 0006> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C)
da1 at ahc0 bus 0 target 2 lun 0
da1: <SEAGATE ST336607LW 0006> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da1: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C)
em0: Link is up 100 Mbps Full Duplex
С уважением Илья Байдаков.
--- ifmail v.2.15dev5.3
* Origin: PeterStar News Site (2:5020/400)
Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
|
