|
ru.linux
- RU.LINUX ---------------------------------------------------------------------
From : Alex Vin 2:5020/400 17 Mar 2006 11:52:05
To : Alex Korchmar
Subject : Re: tar to tape (/dev/st0)
--------------------------------------------------------------------------------
> AV> жму ентер после набора - команда пролетает - а ничего не происходит
> если предварительно ты еще что-то использовал с /dev/st - ничего и не
> произойдет, она и так на начале.
> mt stat тебе это скажет.
SCSI 2 tape drive:
File number=0, block number=0, partition=0.
Tape block size 0 bytes. Density code 0x42 (no translation).
Soft error count since last status=0
General status bits on (41010000):
BOT ONLINE IM_REP_EN
а где тут слова, что лента стоит на начале? File number=0, block number=0 ?
> AV> а линукс постоит-постоит да высыпет дамп драйвера
> не знаю что такое дамп драйвера, а если это ошибка - покажи сообщение.
> и вообще, видимо все из dmesg что имело к ней отношение.
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
<Adaptec 29320ALP Ultra320 SCSI adapter>
aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512
SCBs
(scsi0:A:3): 160.000MB/s transfers (80.000MHz DT, 16bit)
Vendor: HP Model: Ultrium 2-SCSI Rev: S24D
Type: Sequential-Access ANSI SCSI revision: 03
st: Version 20040403, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi0, channel 0, id 3, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575
===========================
Mar 14 15:54:54 rabbit kernel: scsi0: Transmission error detected
Mar 14 15:54:54 rabbit kernel: LQISTAT1[0x0] LASTPHASE[0x80] SCSISIGI[0x40]
PERRDIAG[0x1]
Mar 14 15:54:54 rabbit kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Mar 14 15:54:54 rabbit kernel: scsi0: Dumping Card State at program address
0x196 Mode 0x11
Mar 14 15:54:54 rabbit kernel: Card was paused
Mar 14 15:54:54 rabbit kernel: HS_MAILBOX[0x0] INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11]
Mar 14 15:54:54 rabbit kernel: DFFSTAT[0x19] SCSISIGI[0x56] SCSIPHASE[0x2]
SCSIBUS[0x70]
Mar 14 15:54:54 rabbit kernel: LASTPHASE[0x80] SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0]
Mar 14 15:54:54 rabbit kernel: SEQINTCTL[0x0] SEQ_FLAGS[0x0] SEQ_FLAGS2[0x0]
SSTAT0[0x0]
Mar 14 15:54:54 rabbit kernel: SSTAT1[0x19] SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
Mar 14 15:54:54 rabbit kernel: SIMODE1[0xac] LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0]
Mar 14 15:54:54 rabbit kernel: LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x0]
Mar 14 15:54:54 rabbit kernel:
Mar 14 15:54:54 rabbit kernel: SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff
CURRSCB 0x3 NEXTSCB 0x0
Mar 14 15:54:54 rabbit kernel: qinstart = 53961 qinfifonext = 53961
Mar 14 15:54:54 rabbit kernel: QINFIFO:
Mar 14 15:54:54 rabbit kernel: WAITING_TID_QUEUES:
Mar 14 15:54:54 rabbit kernel: Pending list:
Mar 14 15:54:54 rabbit kernel: 3 FIFO_USE[0x0] SCB_CONTROL[0x0]
SCB_SCSIID[0x37]
Mar 14 15:54:54 rabbit kernel: Total 1
Mar 14 15:54:54 rabbit kernel: Kernel Free SCB list: 2 1 0
Mar 14 15:54:54 rabbit kernel: Sequencer Complete DMA-inprog list:
Mar 14 15:54:54 rabbit kernel: Sequencer Complete list:
Mar 14 15:54:54 rabbit kernel: Sequencer DMA-Up and Complete list:
Mar 14 15:54:54 rabbit kernel:
Mar 14 15:54:54 rabbit kernel: scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
Mar 14 15:54:54 rabbit kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0]
DFSTATUS[0x89]
Mar 14 15:54:54 rabbit kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Mar 14 15:54:54 rabbit kernel: SOFFCNT[0x1] MDFFSTAT[0x5] SHADDR = 0x00,
SHCNT = 0x0
Mar 14 15:54:54 rabbit kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Mar 14 15:54:54 rabbit kernel: scsi0: FIFO1 Active, LONGJMP == 0x81d1, SCB
0x3
Mar 14 15:54:54 rabbit kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x4]
DFSTATUS[0x88]
Mar 14 15:54:54 rabbit kernel: SG_CACHE_SHADOW[0x3] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Mar 14 15:54:54 rabbit kernel: SOFFCNT[0x1] MDFFSTAT[0x14] SHADDR = 0x06,
SHCNT = 0x0
Mar 14 15:54:54 rabbit kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Mar 14 15:54:54 rabbit kernel: LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Mar 14 15:54:54 rabbit kernel: scsi0: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Mar 14 15:54:54 rabbit kernel: scsi0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
Mar 14 15:54:54 rabbit kernel: SIMODE0[0xc]
Mar 14 15:54:54 rabbit kernel: CCSCBCTL[0x4]
Mar 14 15:54:54 rabbit kernel: scsi0: REG0 == 0x3, SINDEX = 0x180, DINDEX =
0x108
Mar 14 15:54:54 rabbit kernel: scsi0: SCBPTR == 0x3, SCB_NEXT == 0xffc0,
SCB_NEXT2 == 0xff45
Mar 14 15:54:54 rabbit kernel: CDB 3 0 0 0 20 0
Mar 14 15:54:54 rabbit kernel: STACK: 0xc3 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Mar 14 15:54:54 rabbit kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Mar 14 15:54:54 rabbit kernel: DevQ(0:3:0): 0 waiting
Mar 14 15:54:54 rabbit kernel: scsi0:0:3:0: Attempting to abort cmd f745b080:
0x0 0x0 0x0 0x0 0x0 0x0
Mar 14 15:54:54 rabbit kernel: scsi0: At time of recovery, card was not
paused
Mar 14 15:54:54 rabbit kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins
<<<<<<<<<<<<<<<<<
Mar 14 15:54:54 rabbit kernel: scsi0: Dumping Card State at program address
0x1e Mode 0x0
Mar 14 15:54:54 rabbit kernel: Card was paused
Mar 14 15:54:54 rabbit kernel: HS_MAILBOX[0x0] INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11]
Mar 14 15:54:54 rabbit kernel: DFFSTAT[0x19] SCSISIGI[0x56] SCSIPHASE[0x0]
SCSIBUS[0x70]
Mar 14 15:54:54 rabbit kernel: LASTPHASE[0x40] SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0]
Mar 14 15:54:54 rabbit kernel: SEQINTCTL[0x0] SEQ_FLAGS[0x20] SEQ_FLAGS2[0x0]
SSTAT0[0x0]
Mar 14 15:54:54 rabbit kernel: SSTAT1[0x8] SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
Mar 14 15:54:54 rabbit kernel: SIMODE1[0xac] LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0]
Mar 14 15:54:54 rabbit kernel: LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x0]
Mar 14 15:54:54 rabbit kernel:
Mar 14 15:54:54 rabbit kernel: SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff
CURRSCB 0x3 NEXTSCB 0x0
Mar 14 15:54:54 rabbit kernel: qinstart = 53961 qinfifonext = 53961
Mar 14 15:54:54 rabbit kernel: QINFIFO:
Mar 14 15:54:54 rabbit kernel: WAITING_TID_QUEUES:
Mar 14 15:54:54 rabbit kernel: Pending list:
Mar 14 15:54:54 rabbit kernel: 3 FIFO_USE[0x0] SCB_CONTROL[0x0]
SCB_SCSIID[0x37]
Mar 14 15:54:54 rabbit kernel: Total 1
Mar 14 15:54:54 rabbit kernel: Kernel Free SCB list: 2 1 0
Mar 14 15:54:54 rabbit kernel: Sequencer Complete DMA-inprog list:
Mar 14 15:54:54 rabbit kernel: Sequencer Complete list:
Mar 14 15:54:54 rabbit kernel: Sequencer DMA-Up and Complete list:
Mar 14 15:54:54 rabbit kernel:
Mar 14 15:54:54 rabbit kernel: scsi0: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
Mar 14 15:54:54 rabbit kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0]
DFSTATUS[0x89]
Mar 14 15:54:54 rabbit kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Mar 14 15:54:54 rabbit kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00,
SHCNT = 0x0
Mar 14 15:54:54 rabbit kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Mar 14 15:54:54 rabbit kernel: scsi0: FIFO1 Active, LONGJMP == 0x81d1, SCB
0x3
Mar 14 15:54:54 rabbit kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x28]
DFSTATUS[0x80]
Mar 14 15:54:54 rabbit kernel: SG_CACHE_SHADOW[0xa] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Mar 14 15:54:54 rabbit kernel: SOFFCNT[0x0] MDFFSTAT[0xc] SHADDR =
0x03745a300, SHCNT = 0x20
Mar 14 15:54:54 rabbit kernel: HADDR = 0x03745a300, HCNT = 0x20 CCSGCTL[0x10]
Mar 14 15:54:54 rabbit kernel: LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Mar 14 15:54:54 rabbit kernel: scsi0: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Mar 14 15:54:54 rabbit kernel: scsi0: OS_SPACE_CNT = 0x1f MAXCMDCNT = 0x0
Mar 14 15:54:54 rabbit kernel: SIMODE0[0xc]
Mar 14 15:54:54 rabbit kernel: CCSCBCTL[0x4]
Mar 14 15:54:54 rabbit kernel: scsi0: REG0 == 0xcad8, SINDEX = 0x180, DINDEX
= 0x108
Mar 14 15:54:54 rabbit kernel: scsi0: SCBPTR == 0x0, SCB_NEXT == 0xff00,
SCB_NEXT2 == 0x0
Mar 14 15:54:54 rabbit kernel: CDB 0 0 0 0 0 0
Mar 14 15:54:54 rabbit kernel: STACK: 0x1ea 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Mar 14 15:54:54 rabbit kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Mar 14 15:54:54 rabbit kernel: DevQ(0:3:0): 0 waiting
Mar 14 15:54:54 rabbit kernel: scsi0:0:3:0: Device is active, asserting ATN
Mar 14 15:54:54 rabbit kernel: Recovery code sleeping
Mar 14 15:54:59 rabbit kernel: Recovery code awake
Mar 14 15:54:59 rabbit kernel: Timer Expired
Mar 14 15:54:59 rabbit kernel: Recovery code sleeping
Mar 14 15:55:04 rabbit kernel: Recovery code awake
Mar 14 15:55:04 rabbit kernel: Timer Expired
Mar 14 15:55:04 rabbit kernel: scsi0: Device reset returning 0x2003
Mar 14 15:55:04 rabbit kernel: Recovery SCB completes
Mar 14 15:55:04 rabbit kernel: Recovery SCB completes
Mar 14 15:55:14 rabbit kernel: st0: Error 6000000 (sugg. bt 0x0, driver bt
0x6, host bt 0x0).
================================
Mar 16 12:22:50 rabbit kernel: st0: Error with sense data: Current st0: sense
key Not Ready
Mar 16 12:22:50 rabbit kernel: Additional sense: Logical unit has not
self-configured yet
Mar 16 12:22:50 rabbit kernel: st0: Error on write filemark.
Mar 16 12:22:50 rabbit kernel: st0: Error with sense data: Current st0: sense
key Not Ready
Mar 16 12:22:50 rabbit kernel: Additional sense: Logical unit has not
self-configured yet
Mar 16 12:24:17 rabbit kernel: st0: Error 10000 (sugg. bt 0x0, driver bt 0x0,
host bt 0x1).
Mar 16 12:24:17 rabbit kernel: st0: Error 10000 (sugg. bt 0x0, driver bt 0x0,
host bt 0x1).
==================================
--- ifmail v.2.15dev5.3
* Origin: ZAO "InT" InterNetNews site (2:5020/400)
Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
|
