|
ru.cisco
- RU.CISCO ---------------------------------------------------------------------
From : Roman D. Sinjuk 2:5020/400 19 Jun 2003 00:04:45
To : Alex Grey
Subject : Re: странности на PA-A3-E3
--------------------------------------------------------------------------------
Alex Grey <kiral@skynet.be> wrote:
> Hello, Roman!
> You wrote on Tue, 17 Jun 2003 10:57:04 +0000 (UTC):
>
> RDS> Есть две 7200 связаные по ATM через PA-A3-E3. Если включить "debug atm
> RDS> events" т о иногда (гдето раз в минуту) проскакивает фигня следующего
> RDS> вида:
>
> RDS> 10w6d: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0000
> RDS> 10w6d: mgmt interrupt status 0x00000240
> RDS> 10w6d: e3 frmr interrupt status 0x00
> RDS> 10w6d: e3 alarm maint_int 0x18 status 0x68 alarm 0x0010
> RDS> 10w6d: atmdx_alarm_handler(ATM1/0): alarm 0x0010, state 4
> RDS> 10w6d: ATM1/0: LED turned 1
> RDS> 10w6d: pmc_pm7345_isr: received framer int 0x08, old alarm 0x0010
> RDS> 10w6d: mgmt interrupt status 0x00000240
> RDS> 10w6d: e3 frmr interrupt status 0x00
> RDS> 10w6d: e3 alarm maint_int 0x18 status 0x08 alarm 0x0000
>
> RDS> Еще иногда (раз-два за сутки) у интерфейса PA-A3-E3 конкретно срывает
> RDS> крышу, перестают проходить OAM-ы, при этом физичский интерфейс atm1/0
> RDS> в up-е, а сабинтерфейс atm1/0.2 в down и при включеном дебаге валится:
>
> RDS> 1w1d: ATM(ATM1/0.2): VCD#2 VC 0/107 failed to echo OAM. 37 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#3 VC 0/106 failed to echo OAM. 37 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#7 VC 0/102 failed to echo OAM. 54 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#9 VC 0/100 failed to echo OAM. 40 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#6 VC 0/103 failed to echo OAM. 38 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#5 VC 0/104 failed to echo OAM. 55 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#4 VC 0/105 failed to echo OAM. 55 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#8 VC 0/101 failed to echo OAM. 38 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#2 VC 0/107 failed to echo OAM. 38 tries
> RDS> 1w1d: ATM(ATM1/0.2): VCD#3 VC 0/106 failed to echo OAM. 38 tries
> RDS> ...
>
>
> когда еще раз сорвет собери
> 'show ver'
> 'show int a1/0' 3 раза подряд
> 'show contr a1/0' 3 раза подряд
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JS-M), Version 12.2(11)T6, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Wed 12-Feb-03 23:51 by ccai
Image text-base: 0x60008940, data-base: 0x61C2C000
ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT
SOFTWARE
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT
RELEASE SOFTWARE (fc1)
tom uptime is 2 weeks, 3 days, 3 hours, 2 minutes
System returned to ROM by reload at 19:57:54 EEST Sun Jun 1 2003
System restarted at 19:22:57 EEST Sun Jun 1 2003
System image file is "slot0:c7200-js-mz.122-11.T6.bin"
cisco 7206VXR (NPE300) processor (revision B) with 229376K/65536K bytes of
memory.
Processor board ID 23662415
R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
6 slot VXR midplane, Version 2.1
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 FastEthernet/IEEE 802.3 interface(s)
8 Serial network interface(s)
1 ATM network interface(s)
125K bytes of non-volatile configuration memory.
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x102
ATM1/0 is up, line protocol is up
Hardware is ENHANCED ATM PA
MTU 4470 bytes, sub MTU 4470, BW 33920 Kbit, DLY 200 usec,
reliability 255/255, txload 21/255, rxload 36/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5
4095 maximum active VCs, 9 current VCCs
VC idle disconnect time: 300 seconds
5479066 carrier transitions
Last input 00:00:53, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/29526/23 (size/max/drops/flushes); Total output drops:
1159116
Queueing strategy: None
5 minute input rate 4822000 bits/sec, 685 packets/sec
5 minute output rate 2895000 bits/sec, 619 packets/sec
1737400429 packets input, 2405002057 bytes, 94 no buffer
Received 0 broadcasts, 0 runts, 7 giants, 0 throttles
746332 input errors, 746332 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1412571237 packets output, 331920151 bytes, 0 underruns
1400 output errors, 0 collisions, 156 interface resets
0 output buffer failures, 0 output buffers swapped out
ATM1/0.2 is down, line protocol is down
Hardware is ENHANCED ATM PA
Description: Microwave link
Internet address is 193.125.78.82/30
MTU 4470 bytes, BW 34000 Kbit, DLY 200 usec,
reliability 255/255, txload 21/255, rxload 36/255
Encapsulation ATM
38826529471 packets input, 0 cells, 1736547591083 bytes
13208471457 packets output, 0 cells, 523283589913 bytes
19575537 OAM cells input, 19758566 OAM cells output
AAL5 CRC errors : 16939
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 7
Interface ATM1/0 is up
Hardware is ENHANCED ATM PA - E3 (34000Kbps)
Framer is PMC PM7345 S/UNI-PDH, SAR is LSI ATMIZER II
Firmware rev: G136, Framer rev: 1, ATMIZER II rev: 3
idb=0x630F1040, ds=0x630F8A00, vc=0x6313E960
slot 1, unit 1, subunit 0, fci_type 0x005D, ticks 9465
2400 rx buffers: size=512, encap=64, trailer=28, magic=4
Curr Stats:
VCC count: current=9, peak=9
AAL2 VCC count: 0
AAL2 TX no buffer count: 0
AAL2 RX no buffer count: 0
SAR crashes: Rx SAR=0, Tx SAR=0
rx_cell_lost=3476, rx_no_buffer=0, rx_crc_10=24
rx_cell_len=0, rx_no_vcd=4417, rx_cell_throttle=0, tx_aci_err=0
Rx Free Ring status:
base=0x3CA78040, size=4096, write=1920
Rx Compl Ring status:
base=0x7000AE20, size=4096, read=1443
Tx Ring status:
base=0x3CF137C0, size=8192, write=833
Tx Compl Ring status:
base=0x20012E60, size=4096, read=416
BFD Cache status:
base=0x631388E0, size=6144, read=6142
Rx Cache status:
base=0x6312F480, size=16, write=2
Tx Shadow status:
base=0x63130860, size=8192, read=831, write=833
Control data:
rx_max_spins=24, max_tx_count=141, tx_count=2
rx_threshold=1600, rx_count=3, tx_threshold=4608
tx bfd write indx=0x2A, rx_pool_info=0x6312F520
Control data base address:
rx_buf_base = 0x0E1979A0 rx_p_base = 0x63104700
rx_pak = 0x6312F144 cmd = 0x63104100
framer = 0x60406B54 framer_cb = 0x63104500
framer_base = 0x3C900000 pci_pa_stats = 0x70016EA0
device_base[0] = 0x3C800000 device_base[1] = 0x3CC00000
ssram_base[0] = 0x3CA00000 ssram_base[1] = 0x3CE00000
sdram_base[0] = 0x3CB00000 sdram_base[1] = 0x3CF00000
pa_cmd_buf[0] = 0x3CA7FC00 pa_cmd_buf[1] = 0x3CE7FC00
vcd_base[0] = 0x3CA00000 vcd_base[1] = 0x3CE18000
chip_dump[0] = 0x20016EC4 chip_dump[1] = 0x20016FB4
sar_buf_base[0] = 0x3CB1C000 sar_buf_base[1] = 0x3CF1C000
bfd_base[0] = 0x3CA60000 bfd_base[1] = 0x3CE00000
acd_base[0] = 0x3CA20080 acd_base[1] = 0x3CE38240
Framer Information:
Framing mode: E3 G832 ADM
No alarm detected
Facility statistics: current interval elapsed 465 seconds
lcv fbe ezd pe ppe febe hcse
lcv: Line Code Violation
be: Framing Bit Error
ezd: Summed Excessive Zeros
pe: Parity Error
ppe: Path Parity Error
febe: Far-end Block Error
hcse: Rx Cell HCS Error
ATM1/0 is up, line protocol is up
Hardware is ENHANCED ATM PA
MTU 4470 bytes, sub MTU 4470, BW 33920 Kbit, DLY 200 usec,
reliability 255/255, txload 21/255, rxload 36/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5
4095 maximum active VCs, 9 current VCCs
VC idle disconnect time: 300 seconds
5479066 carrier transitions
Last input 00:00:55, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/29526/23 (size/max/drops/flushes); Total output drops:
1159116
Queueing strategy: None
5 minute input rate 4822000 bits/sec, 685 packets/sec
5 minute output rate 2895000 bits/sec, 619 packets/sec
1737400429 packets input, 2405002057 bytes, 94 no buffer
Received 0 broadcasts, 0 runts, 7 giants, 0 throttles
746332 input errors, 746332 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1412571250 packets output, 331920827 bytes, 0 underruns
1400 output errors, 0 collisions, 156 interface resets
0 output buffer failures, 0 output buffers swapped out
ATM1/0.2 is down, line protocol is down
Hardware is ENHANCED ATM PA
Description: Microwave link
Internet address is 193.125.78.82/30
MTU 4470 bytes, BW 34000 Kbit, DLY 200 usec,
reliability 255/255, txload 21/255, rxload 36/255
Encapsulation ATM
38826529471 packets input, 0 cells, 1736547591083 bytes
13208471457 packets output, 0 cells, 523283589913 bytes
19575537 OAM cells input, 19758578 OAM cells output
AAL5 CRC errors : 16939
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 7
Interface ATM1/0 is up
Hardware is ENHANCED ATM PA - E3 (34000Kbps)
Framer is PMC PM7345 S/UNI-PDH, SAR is LSI ATMIZER II
Firmware rev: G136, Framer rev: 1, ATMIZER II rev: 3
idb=0x630F1040, ds=0x630F8A00, vc=0x6313E960
slot 1, unit 1, subunit 0, fci_type 0x005D, ticks 9467
2400 rx buffers: size=512, encap=64, trailer=28, magic=4
Curr Stats:
VCC count: current=9, peak=9
AAL2 VCC count: 0
AAL2 TX no buffer count: 0
AAL2 RX no buffer count: 0
SAR crashes: Rx SAR=0, Tx SAR=0
rx_cell_lost=3476, rx_no_buffer=0, rx_crc_10=24
rx_cell_len=0, rx_no_vcd=4417, rx_cell_throttle=0, tx_aci_err=0
Rx Free Ring status:
base=0x3CA78040, size=4096, write=1920
Rx Compl Ring status:
base=0x7000AE20, size=4096, read=1443
Tx Ring status:
base=0x3CF137C0, size=8192, write=846
Tx Compl Ring status:
base=0x20012E60, size=4096, read=423
BFD Cache status:
base=0x631388E0, size=6144, read=6143
Rx Cache status:
base=0x6312F480, size=16, write=2
Tx Shadow status:
base=0x63130860, size=8192, read=831, write=846
Control data:
rx_max_spins=24, max_tx_count=141, tx_count=15
rx_threshold=1600, rx_count=3, tx_threshold=4608
tx bfd write indx=0x10DF, rx_pool_info=0x6312F520
Control data base address:
rx_buf_base = 0x0E1979A0 rx_p_base = 0x63104700
rx_pak = 0x6312F144 cmd = 0x63104100
framer = 0x60406B54 framer_cb = 0x63104500
framer_base = 0x3C900000 pci_pa_stats = 0x70016EA0
device_base[0] = 0x3C800000 device_base[1] = 0x3CC00000
ssram_base[0] = 0x3CA00000 ssram_base[1] = 0x3CE00000
sdram_base[0] = 0x3CB00000 sdram_base[1] = 0x3CF00000
pa_cmd_buf[0] = 0x3CA7FC00 pa_cmd_buf[1] = 0x3CE7FC00
vcd_base[0] = 0x3CA00000 vcd_base[1] = 0x3CE18000
chip_dump[0] = 0x20016EC4 chip_dump[1] = 0x20016FB4
sar_buf_base[0] = 0x3CB1C000 sar_buf_base[1] = 0x3CF1C000
bfd_base[0] = 0x3CA60000 bfd_base[1] = 0x3CE00000
acd_base[0] = 0x3CA20080 acd_base[1] = 0x3CE38240
Framer Information:
Framing mode: E3 G832 ADM
No alarm detected
Facility statistics: current interval elapsed 467 seconds
lcv fbe ezd pe ppe febe hcse
----------------------------------------------------------------------
lcv: Line Code Violation
be: Framing Bit Error
ezd: Summed Excessive Zeros
pe: Parity Error
ppe: Path Parity Error
febe: Far-end Block Error
hcse: Rx Cell HCS Error
ATM1/0 is up, line protocol is up
Hardware is ENHANCED ATM PA
MTU 4470 bytes, sub MTU 4470, BW 33920 Kbit, DLY 200 usec,
reliability 255/255, txload 21/255, rxload 35/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5
4095 maximum active VCs, 9 current VCCs
VC idle disconnect time: 300 seconds
5479066 carrier transitions
Last input 00:00:57, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/29526/23 (size/max/drops/flushes); Total output drops:
1159116
Queueing strategy: None
5 minute input rate 4739000 bits/sec, 673 packets/sec
5 minute output rate 2845000 bits/sec, 607 packets/sec
1737400429 packets input, 2405002057 bytes, 94 no buffer
Received 0 broadcasts, 0 runts, 7 giants, 0 throttles
746332 input errors, 746332 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1412571260 packets output, 331921347 bytes, 0 underruns
1400 output errors, 0 collisions, 156 interface resets
0 output buffer failures, 0 output buffers swapped out
ATM1/0.2 is down, line protocol is down
Hardware is ENHANCED ATM PA
Description: Microwave link
Internet address is 193.125.78.82/30
MTU 4470 bytes, BW 34000 Kbit, DLY 200 usec,
reliability 255/255, txload 21/255, rxload 35/255
Encapsulation ATM
38826529471 packets input, 0 cells, 1736547591083 bytes
13208471457 packets output, 0 cells, 523283589913 bytes
19575537 OAM cells input, 19758578 OAM cells output
AAL5 CRC errors : 16939
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 7
Interface ATM1/0 is up
Hardware is ENHANCED ATM PA - E3 (34000Kbps)
Framer is PMC PM7345 S/UNI-PDH, SAR is LSI ATMIZER II
Firmware rev: G136, Framer rev: 1, ATMIZER II rev: 3
idb=0x630F1040, ds=0x630F8A00, vc=0x6313E960
slot 1, unit 1, subunit 0, fci_type 0x005D, ticks 9469
2400 rx buffers: size=512, encap=64, trailer=28, magic=4
Curr Stats:
VCC count: current=9, peak=9
AAL2 VCC count: 0
AAL2 TX no buffer count: 0
AAL2 RX no buffer count: 0
SAR crashes: Rx SAR=0, Tx SAR=0
rx_cell_lost=3476, rx_no_buffer=0, rx_crc_10=24
rx_cell_len=0, rx_no_vcd=4417, rx_cell_throttle=0, tx_aci_err=0
Rx Free Ring status:
base=0x3CA78040, size=4096, write=1920
Rx Compl Ring status:
base=0x7000AE20, size=4096, read=1443
Tx Ring status:
base=0x3CF137C0, size=8192, write=855
Tx Compl Ring status:
base=0x20012E60, size=4096, read=427
BFD Cache status:
base=0x631388E0, size=6144, read=6142
Rx Cache status:
base=0x6312F480, size=16, write=2
Tx Shadow status:
base=0x63130860, size=8192, read=847, write=855
Control data:
rx_max_spins=24, max_tx_count=141, tx_count=8
rx_threshold=1600, rx_count=3, tx_threshold=4608
tx bfd write indx=0x1C, rx_pool_info=0x6312F520
Control data base address:
rx_buf_base = 0x0E1979A0 rx_p_base = 0x63104700
rx_pak = 0x6312F144 cmd = 0x63104100
framer = 0x60406B54 framer_cb = 0x63104500
framer_base = 0x3C900000 pci_pa_stats = 0x70016EA0
device_base[0] = 0x3C800000 device_base[1] = 0x3CC00000
ssram_base[0] = 0x3CA00000 ssram_base[1] = 0x3CE00000
sdram_base[0] = 0x3CB00000 sdram_base[1] = 0x3CF00000
pa_cmd_buf[0] = 0x3CA7FC00 pa_cmd_buf[1] = 0x3CE7FC00
vcd_base[0] = 0x3CA00000 vcd_base[1] = 0x3CE18000
chip_dump[0] = 0x20016EC4 chip_dump[1] = 0x20016FB4
sar_buf_base[0] = 0x3CB1C000 sar_buf_base[1] = 0x3CF1C000
bfd_base[0] = 0x3CA60000 bfd_base[1] = 0x3CE00000
acd_base[0] = 0x3CA20080 acd_base[1] = 0x3CE38240
Framer Information:
Framing mode: E3 G832 ADM
No alarm detected
Facility statistics: current interval elapsed 469 seconds
lcv fbe ezd pe ppe febe hcse
----------------------------------------------------------------------
lcv: Line Code Violation
be: Framing Bit Error
ezd: Summed Excessive Zeros
pe: Parity Error
ppe: Path Parity Error
febe: Far-end Block Error
hcse: Rx Cell HCS Error
>
>
--- ifmail v.2.15dev5
* Origin: Unknown (2:5020/400)
Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
|
Re: странности на PA-A3-E3 