|
ru.cisco
- RU.CISCO ---------------------------------------------------------------------
From : oleg yakunin 2:5020/400 04 Sep 2002 14:53:58
To : Alekseev Aleksey
Subject : Re: асинхра выделенка
--------------------------------------------------------------------------------
Alekseev Aleksey <A.Alekseev@chatcom.cjb.net> пишет:
AA> ppp
oy>> stopbits 1
oy>> speed 115200
oy>> flowcontrol hardware
AA> а на какой скорости у тебя модемы связаались??
AA> такую и поставь на линии...
AA> ВОЛКА
требовалось получить v.32 9600
вбивал я rxspeed/txspeed
тока он в line 2 не отразился почему-то
правда это видно вот так вот
это два состояния линии в up и в down
результат нулевой
20:00:55: %LINK-3-UPDOWN: Interface Serial0/1, changed state to up
sh line 2
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
Overruns Int
A 2 TTY 9600/9600 - inout - - - 0 0
0/0 Se0/1
Line 2, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits
Status: Ready, Active, No Exit Banner, Async Interface Active
HW PPP Support Active, CTS Raised
Capabilities: EXEC Suppressed, Hardware Flowcontrol In,
Hardware Flowcontrol Out, Modem Callout, Modem RI is CD,
Line is permanent async interface
Modem state: Ready
Line is running PPP.
0 output packets queued, 1 input packets.
Async Escape map is 11111111111111111111111111111111
Modem hardware state: CTS DSR DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session
Dispatch
00:10:00 never none
not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: 00:00:13
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are none.
Allowed output transports are pad v120 telnet rlogin.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters
Router2#sh line 2
20:01:17: %LINK-5-CHANGED: Interface Serial0/1, changed state to reset
20:01:22: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
Overruns Int
2 TTY 9600/9600 - inout - - - 0 0
0/0 Se0/1
Line 2, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits
Status: No Exit Banner, CTS Raised
Capabilities: EXEC Suppressed, Hardware Flowcontrol In,
Hardware Flowcontrol Out, Modem Callout, Modem RI is CD,
Line is permanent async interface
Modem state: Idle
Modem hardware state: CTS DSR DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session
Dispatch
00:10:00 never none
not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: 00:00:00
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are none.
Allowed output transports are pad v120 telnet rlogin.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters
--
Отправлено через сервер Форумы@mail.ru - http://talk.mail.ru
--- ifmail v.2.15dev5
* Origin: Talk.ru (2:5020/400)
Вернуться к списку тем, сортированных по: возрастание даты уменьшение даты тема автор
|
