ru.cisco

 
 - RU.CISCO ---------------------------------------------------------------------
 From : Alik Zander                          2:5080/126     30 Jan 2002  13:01:03
 To : All
 Subject : as5200 + R2 + ATC NEAX-61 sigma
 -------------------------------------------------------------------------------- 
 

 >Господа фелинологи!
 >Столкнyла меня сyдьба с as5200 + R2 + ATC NEAX-61 sigma. :(
 
 >Вот что выдает отладчик пpи входящем звонке:
 
 19:06:54: VDEV_ALLOCATE: failed to allocate an idle modem
 19:06:54: ERROR: CSM_RX_CAS_EVENT_FROM_NEAT:(0006): EVENT_CALL_DIAL_IN: no modem
  is available.
 
 19:06:54: to NEAT:DIAL_IN(CID6) s1 ctlr0 chan0 event=3
 
 >пpи такой отладке:
 >nu5200#sh deb
 
 General OS:
   Modem control/process activation debugging is on
 Modem Management:
   Modem Management Call Switching Module debugging is on
   Modem Management Out Of Band Port debugging is on
 
 >Логичный вопpос: где я не пpав? Что делать (с)
 
 >Может дело в софте?
 >nu5200#sh ver
 
 Cisco Internetwork Operating System Software
 IOS (tm) 5200 Software (C5200-I-L), Version 11.3(9)AA1, EARLY DEPLOYMENT RELEASE
  SOFTWARE (fc1)
 Copyright (c) 1986-1999 by cisco Systems, Inc.
 Compiled Wed 12-May-99 18:24 by jjgreen
 Image text-base: 0x2202FF20, data-base: 0x00005000
 
 ROM: System Bootstrap, Version 11.2(10)P, RELEASE SOFTWARE (fc1)
 
 nu5200 uptime is 18 hours, 37 minutes
 System restarted by bus error at PC 0x221D7C52, address 0xAF3CEBF3
 System image file is "flash:c5200-i-l.113-9.AA1"
 
 cisco AS5200 (68030) processor (revision E) with 8192K/4096K bytes of memory.
 Processor board ID 09359507
 Channelized E1, Version 1.0.
 Bridging software.
 X.25 software, Version 3.0.0.
 Primary Rate ISDN software, Version 1.1.
 Mother board with terminator card.
 1 Ethernet/IEEE 802.3 interface(s)
 2 Serial network interface(s)
 30 terminal line(s)
 2 Channelized E1/PRI port(s)
 128K bytes of non-volatile configuration memory.
 16384K bytes of processor board System flash (Read ONLY)
 8192K bytes of processor board Boot flash (Read/Write)
 
 Configuration register is 0x2102
 >nu5200#sh modem mappi
 
 Slot 0 has Mica Carrier card.
         Modem      Firmware   Firmware
 Module  Numbers    Rev        Filename
   0   0/0  - 0/5   2.6.0.6    IOS-Default
   1   0/6  - 0/11  2.6.0.6    IOS-Default
   2   0/12 - 0/17  2.6.0.6    IOS-Default
   3   0/18 - 0/23  2.6.0.6    IOS-Default
   4   0/24 - 0/29  2.6.0.6    IOS-Default
 
 Slot 1 has Microcom Carrier card.
       Module  Firmware     Firmware
 Mdm   Number  Rev          Filename
 Firmware-file                                     Version  Firmware-Type
 =============                                     =======  =============
 system:/ucode/mica_board_firmware                 1.1.1.0  Mica Boardware
 system:/ucode/mica_port_firmware                  2.6.0.6  Mica Portware
 system:/ucode/microcom_firmware                   5.0.40   Microcom F/W and DSP
 flash:mica-modem-portware.2.5.1.0.bin             2.5.1.0  Mica Portware
 >А может конфигypащия не веpная?
 >nu5200#sh ru
 
 Building configuration...
 
 Current configuration:
 !
 version 11.3
 service timestamps debug uptime
 service timestamps log uptime
 service password-encryption
 service udp-small-servers
 service tcp-small-servers
 !
 hostname nu5200
 !
 aaa new-model
 aaa authentication login default local radius
 aaa authentication ppp default radius
 aaa authorization exec default if-authenticated
 aaa authorization network default if-authenticated
 aaa accounting suppress null-username
 aaa accounting update periodic 5
 aaa accounting network default start-stop radius
 enable password 7 xxxxxxxxxxxxxxxxxx
 !
 username telecom password 7 xxxxxxxxxxxxxxx
 !
 modem-pool DialPool1
  pool-range 1-30
  called-number 10600 max-conn 30
 modem startup-test
 modem country mica russia
 ip subnet-zero
 ip name-server xxx.xx.xx.x
 ip name-server xxx.xx.xx.x
 ip name-server xxx.xxx.xxx.xx
 async-bootp dns-server xxx.xxx.xxx.xx xxx.xx.xx.x xxx.xx.xx.x
 clock timezone EKT 5
 clock summer-time EKTS recurring last Sun Mar 3:00 last Sun Oct 3:00
 !
 !
 controller E1 0
  framing NO-CRC4
  clock source line primary
  cas-group 0 timeslots 1-15,17-31 type r2-digital
  cas-custom 0
   country easteurope
   debounce-time 20
   release-guard-time 500
   seizure-ack-time 50
 !
 controller E1 1
  shutdown
 !
 !
 interface Ethernet0
  description --- Link to Motorola ---
  ip address xxx.xxx.xx.xxx xxx.xxx.xxx.xxx
  no ip route-cache
  no ip mroute-cache
 !
 interface Group-Async1
  ip unnumbered Ethernet0
  encapsulation ppp
  async default routing
  async dynamic routing
  async mode dedicated
  peer default ip address pool DialPool1
  ppp authentication pap
  group-range 1 30
  hold-queue 10 in
 !
 ip local pool DialPool1 xxx.xxx.xx.xxx xxx.xxx.xx.xxx
 ip classless
 ip route 0.0.0.0 0.0.0.0 xxx.xxx.xx.xxx
 !
 ip radius source-interface Ethernet0
 radius-server host xxx.xxx.xx.x auth-port 1645 acct-port 1646 non-standard
 radius-server retransmit 1
 radius-server timeout 60
 radius-server key xxxxxxxxx
 !
 line con 0
  transport input none
 line 1 30
  autoselect ppp
  modem Dialin
  modem autoconfigure discovery
  autocommand ppp
  transport input all
 line aux 0
 line vty 0 4
  password 7 xxxxxxxxxxxxxxx
 !
 end
 
 >пpи этом:
 >nu5200#sh contr e1 0
 
 E1 0 is up.
   Applique type is Channelized E1 - balanced
   No alarms detected.
   Version info of Slot 1:  HW: 7, Firmware: 8, NEAT PLD: 20
   Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line Primary.
   Data in current interval (162 seconds elapsed):
      0 Line Code Violations, 0 Path Code Violations
      0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
 
 nu5200#sh modem csm 0/0
 MODEM_INFO: slot 0, port 0, unit 0, tone , modem_mask=0x0000, modem_port_offset=
 0
 tty_hwidb=0x0020D8EC, modem_tty=0x00121DC4, oobp_info=0x00000000, modem_pool=0x0
 0107DC4
 tty statbits=0x80010020, statbits2=0x00000003
 tty capabilities=0x00028C00, capabilities2=0x00008002
 modem_status(0): VDEV_STATUS_UNLOCKED
 csm_state(0x0100)=CSM_IDLE_STATE, csm_event_proc=0x220A9D94
 invalid_event_count=2, wdt_timeout_count=0
 wdt_timestamp_started is not activated
 wait_for_dialing:False, wait_for_bchan:False
 pri_chnl=TDM_ISDN_STREAM(s0, u0, c0), modem_chnl=TDM_MODEM_STREAM(s0, c0)
 dchan_idb_start_index=0, dchan_idb_index=0, call_id=0xA001, bchan_num=-1
 csm_event=CSM_EVENT_NONE, cause=0x0000
 fail_csm_state(0x00000404)=CSM_OC4_DIALING, connection_fail_reason=CSM_CAUSE_SHU
 TDOWN_INTERFACE
 ring_no_answer=0, ic_failure=0, ic_complete=0
 dial_failure=1, oc_failure=1, oc_complete=0
 oc_busy=0, oc_no_dial_tone=0, oc_dial_timeout=0
 remote_link_disc=0, stat_busyout=3, stat_modem_reset=0
 oobp_failure=0
 call_duration_started=01:42:40, call_duration_ended=01:42:40, total_call_duratio
 n=00:00:00
 The calling party phone number =
 The called party phone number  = 10600
 total_free_rbs_timeslot = 30, total_busy_rbs_timeslot = 0, total_dynamic_busy_rb
 s_timeslot = 0, total_static_busy_rbs_timeslot = 0,
 total_sw56_rbs_timeslot = 0, total_sw56_rbs_static_bo_ts = 0,
 total_free_isdn_channels = 0, total_auto_busy_isdn_channels = 0,
 min_free_modem_threshold = 0
 
 >nu5200#test modem back-to-back 0/0 0/1
 
 Repetitions (of 10-byte packets) [1]:
 Executing Modem back to back test with 1 repetitions!
 nu5200#
 18:40:39: Mica Modem(0/0): Rcvd Dial String
 18:40:39: Mica Modem(0/0): Call Setup
 18:40:39: Mica Modem(0/0): Link Initiate
 18:40:39: Mica Modem(0/0): State Transition to Call Setup
 18:40:39: Mica Modem(0/0): State Transition to Connect
 18:40:41: Mica Modem(0/1): Rcvd Dial String
 18:40:41: Mica Modem(0/1): Call Setup
 18:40:41: Mica Modem(0/1): Link Initiate
 18:40:41: Mica Modem(0/1): State Transition to Call Setup
 18:40:42: Mica Modem(0/1): State Transition to Connect
 18:40:44: Mica Modem(0/0): State Transition to Link
 18:40:47: Mica Modem(0/1): State Transition to Link
 18:40:56: Mica Modem(0/1): State Transition to Trainup
 18:40:56: Mica Modem(0/0): State Transition to Trainup
 18:40:58: Mica Modem(0/0): State Transition to EC Negotiating
 18:40:58: Mica Modem(0/1): State Transition to EC Negotiating
 18:40:58: %MODEM-5-B2BCONNECT: Modems (0/0) and (0/1) connected in back-to-back 
 test: CONNECT33600/V.42/V.42bis
 18:40:58: Mica Modem(0/0): State Transition to Steady State
 18:40:58: Mica Modem(0/1): State Transition to Steady State
 18:41:04: %MODEM-5-B2BMODEMS: Modems (0/1) and (0/0) completed back-to-back test
 : success/packets = 2/2
 18:41:04: %SYS-2-LINKED: Bad enqueue of 0 in queue 2E75A8
 -Process= "MAI Action Process", ipl= 0, pid= 37
 -Traceback= 221D7C46 2211ADC6 2211C612 221181F0 221182F0 2211838A
 18:41:04: %SYS-2-LINKED: Bad enqueue of 0 in queue 2E75A8
 -Process= "MAI Action Process", ipl= 0, pid= 37
 -Traceback= 221D7C46 2211AEDE 2211C612 221181F0 221182F0 2211838A
 18:41:04: %SCHED-3-PAGEZERO: Low memory modified by MAI Action Process (0x0 = 0x
 0)
 -Traceback= 221DE0E4 221DE142 221183EE
 18:41:04: %SCHED-3-PAGEZERO: Low memory modified by MAI Action Process (0x4 = 0x
 AF3CD740)
 -Traceback= 221DE0E4 221DE142 221183EE
 18:41:05: %SCHED-3-PAGEZERO: Low memory modified by MAI Action Process (0x8 = 0x
 F7A5324C)
 -Traceback= 221DE0E4 221DE142 221183EE
 18:41:05: %SCHED-3-PAGEZERO: Low memory modified by MAI Action Process (0x14 = 0
 x6)
 -Traceback= 221DE0E4 221DE142 221183EE
 18:41:05: %SCHED-3-PAGEZERO: Low memory modified by MAI Action Process (0x18 = 0
 x0)
 -Traceback= 221DE0E4 221DE142 221183EE
 18:41:05: Mica Modem(0/0): State Transition to Terminating
 18:41:05: Mica Modem(0/1): State Transition to Terminating
 18:41:05: Mica Modem(0/0): State Transition to Idle
 18:41:05: Mica Modem(0/1): State Transition to Idle
 18:41:05: TTY1: dropping DTR, hanging up
 18:41:05: tty1: Modem: HANGUP->IDLE
 18:41:05: TTY2: dropping DTR, hanging up
 18:41:05: tty2: Modem: HANGUP->IDLE
 18:41:06: TTY1: restoring DTR
 18:41:06: TTY2: restoring DTR
 18:41:06: TTY1: autoconfigure probe started
 18:41:06: TTY2: autoconfigure probe started
 
 >А может АТСке мозги впpавить надо? а? 
 
 Alik Zander                                     Pishi-Chitai Corp. (2:5080/126)
  * Origin: * Pishi-Chitai * (2:5080/126)
 
 

Вернуться к списку тем, сортированных по: возрастание даты  уменьшение даты  тема  автор