ru.cisco

 
 - RU.CISCO ---------------------------------------------------------------------
 From : Slawa Olhovchenkov                   2:5030/500     28 Feb 2006  11:33:14
 To : Nick Maryenko
 Subject : PIX 7.1, failover
 -------------------------------------------------------------------------------- 
 

 
 28 Feb 06, Nick Maryenko writes to Slawa Olhovchenkov:
 
  NM> Hасколько я знаю, для failover over lan необходим отдельный физичекий
  NM> интерфес.
 
 Да, действительно, просто очень криво написали и хорошо запрятали:
 
 http://www.cisco.com/en/US/partner/products/ps6120/products_configuration_guide_
 chapter09186a008054c4b7.html#wp1055300
 
 LAN-Based Failover Link
 
 You can use any unused Ethernet interface on the device as the failover link.
 You cannot specify an interface that is currently configured with a name. The
 failover link interface is not configured as a normal networking interface; it
 exists only for failover communication. This interface should only be used for
 the failover link (and optionally for the Stateful Failover link). You can
 connect the LAN-based failover link by using a dedicated switch with no hosts or
 routers on the link or by using a crossover Ethernet cable to link the units
 directly.
 
 Note When using VLANs, use a dedicated VLAN for the failover link. Sharing the
 failover link VLAN with any other VLANs can cause intermittent traffic problems 
 and ping and ARP failures. If you use a switch to connect the failover link, use
 dedicated interfaces on the switch and security appliance for the failover link;
 do not share the interface with subinterfaces carrying regular network traffic.
 
 http://www.cisco.com/en/US/partner/products/ps6120/products_configuration_guide_
 chapter09186a008054c4b7.html#wp1064158
 
 Step 4 Define the failover interface.
 
 a. Specify the interface to be used as the failover interface.
 
 hostname(config)# failover lan interface if_name phy_if
 
 The if_name argument assigns a name to the interface specified by the phy_if
 argument.
 The phy_if argument can be the physical port name, such as Ethernet1, or a
 previously
 created subinterface, such as Ethernet0/2.3.
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 
  >> А кто-нибудь с данным софтом на 515E вообще работает?
  >> А с failover?
  >>
  >> А то фигня-с. С сериальным линком -- линк становится failed очень быстро.
  >>
  >> А пытаюсь на LAN перейти -- так мне по рукам:
  >>
  >> # failover lan interface failover Ethernet1.111
  >> ERROR: Can not configure failover interface on a shared physical
  >> interface
  >>
  >>
  >> ... Утерянное всегда находишь в последнем каталоге
  NM> --- ifmail v.2.15dev5.3
  NM>  * Origin: ICB (2:5020/400)
 
 ... КЛАВУ топтать - это вам не с ДЖОЙСТИКОМ баловаться...
 --- GoldED+/BSD 1.1.5
  * Origin:  (2:5030/500)
 
 

Вернуться к списку тем, сортированных по: возрастание даты  уменьшение даты  тема  автор 

Тема:    Автор:    Дата:    PIX 7.1, failover   Slawa Olhovchenkov   27 Feb 2006 15:45:56   Re: PIX 7.1, failover   Nick Maryenko   28 Feb 2006 11:27:11   PIX 7.1, failover   Slawa Olhovchenkov   28 Feb 2006 11:33:14