ru.cisco

 
 - RU.CISCO ---------------------------------------------------------------------
 From : Aleksey Cherkasov                    2:5004/48      11 Oct 2006  08:47:55
 To : All
 Subject : Re: Cisco1803 connect with Zyxel-791
 -------------------------------------------------------------------------------- 
 

 
 controller DSL 0
  mode atm
  line-term cpe
  line-mode 2-wire line-zero
  dsl-mode shdsl symmetric annex B
  line-rate auto
 !
 bridge irb
 !
 interface ATM0
  no ip address
  ip virtual-reassembly
  no atm ilmi-keepalive
 interface ATM0.2 multipoint
  pvc 8/35
   encapsulation aal5snap
  !
  bridge-group 1
 !
 interface BVI1
  ip address 1.1.1.1 255.255.255.0
 !
 bridge 1 protocol ieee
 bridge 1 route ip
 !
 ip route 0.0.0.0 0.0.0.0 BVI1
 -- 
 С уважением, Черкасов Алексей.
 г. Омск
 
 -- 
 С уважением, Черкасов Алексей.
 г. Омск
 "Aleksey Cherkasov" <Aleksey_Cherkasov@p131.f48.n5004.z2.fidonet.org> wrote 
 in message news:egfols$5bm$1@mailer.ordi...
 
 > Cisco 1803 (c внутренним модемом) пытаюсь связать с Zyxel791R.
 > Hужно настроить прозрачный бриджинг. Hикак не получается. Кто-нибудь уже 
 > добился результата.
 > ATM0 поднимается.
 > вот мои настройки
 > ------------------------------------------------------------------------------
 > ---------------------------------------- controller DSL 0 mode atm line-term
 > cpe line-mode 2-wire line-zero dsl-mode shdsl symmetric annex B line-rate auto
 >
 > bridge irb
 >
 > interface ATM0
 > no ip address
 > ip virtual-reassembly
 > no atm ilmi-keepalive
 > pvc 8/35
 >  encapsulation aal5snap
 > !
 > bridge-group 1
 >
 > interface BVI1
 > ip address x.x.x.x 255.255.255.0
 >
 > ip route 0.0.0.0 0.0.0.0 BVI1
 >
 > bridge 1 protocol ieee
 >
 > ------------------------------------------------------------------------------
 > ------------------------------- 1803#sh int atm0 ATM0 is up, line protocol is 
 > up Hardware is MPC ATMSAR MTU 4470 bytes, sub MTU 4470, BW 2304 Kbit, DLY 160 
 > usec,    reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ATM,
 > loopback not set Encapsulation(s): AAL5 , PVC mode 23 maximum active VCs, 1024
 > VCs per VP, 1 current VCCs VC Auto Creation Disabled. VC idle disconnect time:
 > 300 seconds Last input 06:22:53, output 00:00:00, output hang never Last
 > clearing of "show interface" counters never Input queue: 0/75/0/0
 > (size/max/drops/flushes); Total output drops: Queueing strategy: Per VC
 > Queueing 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 
 > bits/sec, 0 packets/sec    514 packets input, 45650 bytes, 0 no buffer   
 > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles    0 input errors, 0
 > CRC, 0 frame, 0 overrun, 0 ignored, 0 abort    5653 packets output, 243570
 > bytes, 0 underruns    0 output errors, 0 collisions, 1 interface resets    0
 > output buffer failures, 0 output buffers swapped out Cisco 1803 (MPC8500)
 > processor (revision 0x400) with 118784K/12288K bytes of memory. 1 DSL
 > controller 9 FastEthernet interfaces 1 ISDN Basic Rate interface 1 ATM
 > interface 31360K bytes of ATA CompactFlash (Read/Write) -- С уважением,
 > Черкасов Алексей. г. Омск 
 
 --- Microsoft Outlook Express 6.00.2900.2869
  * Origin: Cherokee Systems (2:5004/48.131@fidonet)
 
 

Вернуться к списку тем, сортированных по: возрастание даты  уменьшение даты  тема  автор 

Тема:    Автор:    Дата:    Cisco1803 connect with Zyxel-791   Aleksey Cherkasov   10 Oct 2006 16:20:58   Re: Cisco1803 connect with Zyxel-791   Aleksey Cherkasov   11 Oct 2006 08:47:55